Description
Microprocessor-controlled measuring and control device, optionally for redox / pH or Poolcare (time-controlled) / pH, in splash-proof plastic housing, wired ready for connection 230V/50Hz. Display of measuring values on backlit graphical display with alphanumeric characters. Menu navigation via clear text display with selection of the desired language. Operating status, warning and alarm messages in clear text via the status bar on the display. Compact measuring and control device for the measuring options: Free switching between measurement options. By adding the "potentiostatic measuring board for the Poolcontrol DYNAMICS", it is possible to implement additional measuring options.
Characteristics of system unit in wall-mounted case for disinfection and dosing equipment:
Closed, pressure-proof compact measuring cell made of transparent plastic on white PVC plate, for measurement of redox and pH.
The measuring cell includes a sample water monitoring feature. The measuring water supply is controlled via an additional ball valve. Integrated flow control monitoring module for connection to the measuring device. Return of the sample water into the water circulation is planned.
The fiber filter is used to retain impurities in the sample water to prevent entry in the measuring cell. Fiber filter with transparent filter cup and cleanable strainer, small mesh size, standardized connections for installation in front of a measuring cell.
Measuring accessories for measurement of the parameters redox and pH.
This includes:
Microprocessor-controlled peristaltic dosing pump for an automatic addition of any kind of liquid media. With gear motor, ball bearing rotor axis and infinitely variable digital speed control. Continuous operation with applied mains voltage.
The delivery rate is adjustable via the speed control and by means of different pump hose sizes. With integrated dosing pump hose and hose connector.
Technical data
System enclosure:
Plastic housing, degree of protection: IP 65
System enclosure dimensions:
260 x 260 x 85 mm (W x H x D)
Weight:
approx. 1.5 kg
Mains voltage:
115 / 230 V/AC, 48-63 Hz
Power consumption:
10 VA (without metering technology)
Display:
via large-area graphical display 100 x 30mm
Operation:
Plain text menu with buttons
Language:
Language selection
Operating temperature:
5 to +40 °C
Storage temperature:
-20 to +65 °C
Rel. humidity:
max. 90% at 40 C°, non-condensing
Safety monitoring:
Interfaces:
RS 485:
for connection to dinowin / Profibus gateway / etc.
dinotecNET+:
for connection to dinotecNET+ as a field device
Redox measuring amplifier:
Measuring range:
-1500mV to +1500mV
Resolution:
1 mV
Ambient temperature influence:
50ppm/K (12mV)
Reference temperature:
23 °C
Input resistance:
> 1012 Ohm
Redox measurement:
via dip-type measuring chain without drainage system
Calibration:
not required
pH measuring value amplifier:
Measuring range:
-1500mV to +1500mV
Resolution:
0.01 pH or 1 mV
Ambient temperature influence:
50ppm/K (12mV)
Reference temperature:
23 °C
Input resistance:
1012 Ohm
Calibration pH:
Optional one-point or two-point calibration
Electrode test:
automatically after calibration
Temperature compensation of the pH value:
can be set automatically or manually via PT1000
Temperature:
Temperature input for sensor:
PT1000
Measurement range:
0 to +60 °C (+/-1%)
Inputs/outputs, control behaviour:
Control response:
Selectable P, PI or PID control
Control:
Optional 1-point or 2-point control
Binary outputs:
4 volt-free output relays for chlorine, lower pH and raise pH (pulse length, pulse frequency, on/off), alarm
Alternatively to raising pH:
Flocculation dosing On/Off
Maximum contact load (230V AC):
370W (inductive), 500W (resistive load)
Maximum switching current:
30V/10A, 115V/0.3A, 230V/0.12A
Digital inputs:
Empty alarm chlorine, pH lowering, dosing stop
Analogue output:
0(4)-20mA for single measured value (optional)
Conductor cross-section terminal block:
0.25 - 2.5mm²
Flow valve
Threaded connection for measuring probes:
PG 13.5
Flow monitoring module:
Reed contact with 2-wire cable connection
Min. initial pressure:
0.2 bar
Max. counter pressure:
1 bar
Sample water requirements:
120 l/h
Connection supply and drain:
sample water hose 6/8mm
Material:
Acrylic glass, clear, with wall mount
Dimensions (mm):
70 x 290 x 75 (wxhxd)
Fibre filter
Holder made of
PP black
Filter cup made of
PA transparent
Inlet/outlet
¼“ inside
Operating pressure
max. 8 bar
Operating temperature
min. 0°C to max. 50°C
Mesh size
0.25mm
Dimensions:
58 x 58 x135mm (wxdxh)
Weight
Approx. 0.15 kg
Measuring accessories
Operating temperature:
0 to +45°C
Storage temperature:
+20 to +65°C
Rel. humidity:
max. 90% at 40°C, non-condensing
dinodos EASY
Mains voltage:
230V +/-10 %, 50/60Hz
Power consumption:
approx. 5 VA max.
Protection class:
IP 65
Dimensions housing (w x h x d):
approx. 135 x 65 x 85 mm
Weight:
approx. 0.6 kg
Permissible ambient temperature:
+10 to +50 oC
Drive:
Gear motor
Pump hose:
compl. with connection pieces for suction line D4
Capacity max.:
approx. 0.25-4.5 l/h (infinitely variable), at a counterpressure of max. 1.5 bar
Suction lift max.:
1.80 m
Operation:
Capacity adjustable via potentiometer
Application
For water treatment in swimming pools, hot tubs and the like.
Spare parts
Fibre filter 3/4", connection 8/6mm
with slotted tube 0.5 mm
double-sided hose connection 8/6mm
pH 4.0 buffer solution 50 ml
pH 7.0 buffer solution 50ml
Rx electrode without lead-out system
for dsc compact systems
and Poolcontrol 1000/S/avant
Measuring cable, with integr. reference cable
for potentiometric measurements (chlorine, ozone, pool care),
with plug, length 1.2 m
Special liquid cleaner for all measuring electrodes
Flexible suction line, with cover fitting MÜ 61
without float switch, ball non-return valve and plug
Hose 6/4 mm, DN 4, hose length 1.5 m, for dinodos easy, START, Concept pumps
Deutsch (DE) 
English (UK)